2 Operation
Manual Operation
Operation 3
Disclaimer: Receiver setup instructions are accurate at time of printing and may change without notice. Call Winegard tech line for assistance: 1-800-788-4417.
DIRECTV Receiver Setup
The TRAV’LER antenna is a versatile satellite antenna and can be manually set to find many different satellites
individually. Note: this function is rarely used. The instructions below assume that the TRAV’LER antenna is already in
the stowed position.
The User Menu consists of four choices:
Search Mode, Diagnostics, Installation,
and Exit.
Note: Diagnostic and Installation menus
are not required for normal operation
and should only be entered by a trained
professional.
Press [ENTER] to choose Search Mode.
Press and hold [POWER] for two
seconds or until the TRAV’LER interface
displays “POWER ON.”
Press and hold the [ENTER] button for
two seconds.The TRAV’LER interface
will ask if you wish to enter the User
Menu. Press [SELECT] to choose “Yes,”
and then press [ENTER].
The TRAV’LER interface will ask if
you want to turn the power off. Press
[ENTER] to choose “No” and start a new
search for your chosen satellite. Press
[SELECT] then [ENTER] to choose “Yes”
and turn off the antenna.
The TRAV’LER antenna will remain
in manual mode until you select
“Multi-Sat Mode” again.
The TRAV’LER interface will ask you
to confirm the change. Press [SELECT]
to move the asterisk to “Yes,” and then
press [ENTER]. The TRAV’LER interface
will then acknowledge which satellite
has been selected. Press [ENTER].
Once in the Search Menu, you may
choose from the following: MULTISAT
MODE (normal search mode),
MANUAL 101, MANUAL 110, MANUAL
119, MAIN MENU (returns to the User
Menu), or EXIT (enters the search
routine).
Press [SELECT] to cycle through these
satellites until the asterisk is next to the
satellite you wish to find. Then, press
[ENTER] to select a satellite.
1
2
3 4
5 6
The following instructions assume that the TRAV’LER antenna has found and locked onto
satellites 101°, 110°, 119°, 99° and 103°. There should be an asterisk next to 101°, 110°, and 119°
on the TRAV’LER interface.
In most DIRECTV receivers, the setup is done through the “Repeat Satellite Setup” option in
your receiver manual. The following instructions are based on an H24 receiver. If your receiver
differs from the options shown, you may need to consult your receiver manual. The wording
and display used in your receiver may differ slightly.
For Help, Call 1-800-788-4417.
In your receiver
Menu, you will
need to identify
the Satellite
Menu. The
Satellite Menu
will have an
option for
Satellite Setup.
You may be
required to press
the DASH (-)
before proceeding
(underneath #7
on the remote).
Press Menu on
your remote,
and then select
Parental, Fav’s &
Setup.
Select System
Setup.
Set Dish Type for
04: Slimline-5.
Set the Switch
Type for
02: Multiswitch.
Press Continue.
Your installation
will be verified.
Errors may be
displayed on
the Installation
Status screen.
This is normal to
see one or two
boxes with an X
instead of a .
Select Continue.
Select Continue.
Continue with
step 9 on the next
page.
WINEGARD COMPANY
POWER ON
Enter User Menu?
*Yes No
Search Mode*
Diagnostics
Multi-Sat Mode*
Manual 61
Power OFF?
*Yes No
Manual ##
Selected
1 2
3 4
5
6
7 8
(12 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals