Winegard WI3535T Specifications

Satellite InterfaceInstallation/Operation Manual Model WB-2700/WB-2000Made in the U.S.A. U.S. Patent PendingWinegard Company • 3000 Kirkwood St. • B

8After power/data cable and coax cable(s) have been routed to Satellite Interface, seal under-neath cable entry plate with approved sealant and screw

93.4 Connect Satellite Antenna to Satellite InterfaceLocate the primary coax cable from rooftop antenna. Connect it to “Sat Antenna In” on the Satel

10 (110°) HD CONVERTERMODEL WB-1100WINEGARD COMPANY • BURLINGTON, IOWATO RECEIVERTO INTERFACE/DISH TO CONTROLMade in USASAT. ANTENNAINSAT. RE

113.5.2 Connect the Satellite Interface to Primary DISH Network or ExpressVu HD ReceiverUsing the mini coax cable provided with the Satellite Interfa

123.7 Install Software Update with Clone Box (if necessary)It may be necessary to install a software update to your previously installed Winegard Sat

13After the software has been loaded, you are ready to proceed to the next step.If you are installing the HD Satellite Interface as an add-on and have

144. DIRECTV Operation4.1 DIRECTV OverviewWhen connected to a Winegard automatic satellite antenna, the Winegard HD satellite In-terface is capable

15Congure DIRECTV Receiver Antenna TypeYou must set your DIRECTV receiver to the “Oval Dish, 3 Satellites” Dish Type. As many DIRECTV receivers have

16Example of DIRECTV Satellite Switching.For a brief example of DIRECTV satellite switching, read the following example.You have powered on the dish,

175. DISH Network Operation5.1 DISH Network OverviewWhen connected to a Winegard Automatic Satellite System, the Winegard HD satellite Interface is

18You must now choose if you subscribe to DISH 500 or DISH 1000 programming. Call DISH Network customer service if you are unsure of your programming

19After unit enters Sleep Mode, you now have 6 minutes to run the check switch test.Press the “Menu” button on the DISH Network remote control.Select

205.3 Watching DISH Network programmingPower on the Winegard Satellite Interface. In a few moments, the satellite antenna will be-gin its search rou

216. Bell ExpressVu Operation6.1 Bell ExpressVu OverviewWhen connected to a Winegard Automatic Satellite System, the Winegard HD satellite Interfac

22A conrmation message will appear. The satellite antenna will reset and begin its search routine for satellite 91°W . Your satellite antenna is no

23Select “Point Dish/Signal” option “1”. If you do not see signal on your meter, be sure satellite 91 is selected and try a different transponder. A

247. Satellite Interface Menu7.1 Main Menu After the Satellite Interface has been powered on and the antenna has acquired the satellite signal, the

25From the Service Provider menu press [SELECT] until your Satellite Service Provider is selected. DTV → DIRECTV DISH → DISH Network BELL → Bell

26To reset the Satellite Receiver, press and hold the Power button on the Receiver (not on the remote control). The receiver will reset, and after a

27Factory DefaultIf you determine that your satellite antenna is not functioning as expected, you may want to return your system to factory default an

1DisclaimerAlthough every effort has been made to insure the information in this manual is correct and complete, no company shall be held liable for a

28Exit Sleep ModeYou may force the antenna into Tracking Mode at any time while the system is in Sleep Mode.From the Sleep Menu, press [SELECT] to sel

29Default SleepYou may return the Satellite Interface to the factory default sleep time of 7 minutes (420 seconds).From the Sleep Menu, press [SELECT]

307.5 Conguration MenuThe Conguration Menu is only to be used by Winegard Authorized Dealers or under the direction of Winegard personnel. The Con

318. Troubleshooting8.1 LCD Error MessagesThe table below is a list of Satellite Interface error messages that may be displayed on the LCD Status Sc

328.2 Solutions to Common Operating IssuesSymptom SolutionPush power button and Interface does not power up Check that Satellite Interface is connect

33SAT. ANTENNAINSAT. RECEIVER OUTFACTORY USE ONLYHDCTRL 1HDCTRL 2COMM. OUT 1TO SAT.ANTENNA DC INDC OUTTO SATANTENNABLK/REDAppendix A Winegard HDTV

34SAT. ANTENNAINSAT. RECEIVER OUTFACTORY USE ONLYHDCTRL 1HDCTRL 2COMM. OUT 1TO SAT.ANTENNA DC INDC OUTTO SATANTENNABLK/REDAppendix A Winegard HDTV

35SAT. ANTENNAINSAT. RECEIVER OUTFACTORY USE ONLYHDCTRL 1HDCTRL 2COMM. OUT 1TO SAT.ANTENNA DC INDC OUTTO SATANTENNABLK/REDAppendix A Winegard HDTV

36Appendix B. Recommended ReceiversWinegard recommends the following receivers for use with your Winegard Automatic Satellite System. Winegard does

37Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601 • 319/754-0600 Fax 319/754-0787 • www.winegard.com Printed in U.S.A. © 2007 Winegar

2Table of Contents1. Introduction ...

38. Troubleshooting ...31 8

41. INTRODUCTION1.1 System OverviewThe Winegard HD Satellite Interface allows your Winegard Movin’ View and RoadTrip satellite systems to receive ad

51.4 Satellite Interface ComponentsHDTV Satellite InterfaceUser interface for the HD Satellite Interface. Using this panel, the user can select the

62. SAFETY2.1 Installation Safety:Winegard highly recommends the Winegard HD Satellite Interface be installed by a professional installer, as

7If you are installing the HD Satellite Interface as an add-on to a previously installedWinegard Satellite Antenna, you should install the software up